After S&K Renovates Your Kitchen, Use a Cabinet to Make This!

So you’ve hired us to remodel your kitchen and now you’ve got all these old cabinet boxes left over. Hold onto one of them to create this great arts and crafts station for kids! Rachel Pereira, from eHow.com gives a great tutorial on how to complete this quick and easy DIY project that will take your kid’s craft area from disaster to stunner. Everything from a storage area to a chalk board all in one package.

Now there’s quite a bit of work involved with this project, so if it’s something you’re not comfortable with just talk to us and we’d be glad to add it in to your project!

 

Check out this before and after –

 

Things You’ll Need

 

Step 1: Disassemble the Cabinet

Using a mallet or hammer, remove the back of the cabinet from the cabinet face. If drawer slides are attached to the cabinet face inside the cabinet, remove them with a Phillips screwdriver. Use the mallet to loosen the sides and bottom of the cabinet from the cabinet face, as well as the drawer sides and bottom from the drawer face. Needle-nose pliers may be used to remove any staples. Remove pulls or knobs with a screwdriver.

 

Step 2: Build the Desk Base

Measure the length and width of the cabinet face. Using a circular saw, cut a one-by-three pine board into two long pieces that are equivalent to the length of the cabinet face and two short pieces that are 1 1/2 inches shorter than the width of the cabinet face. For example, the cabinet face used in this tutorial is 31 inches long and 21 inches wide. Two boards were cut at 31 inches and two boards were cut at 19 inches. Adjust these measurements depending on the size of your cabinet face.

Drill 3/4-inch pocket holes along the long pieces of wood, spaced about 4 to 5 inches apart. Drill 3/4-inch pocket holes along the long side of the short pieces of wood, and then two pocket holes on either end. Use wood glue and 1 1/4-inch pocket hole screws to screw the short boards to the inside of the long boards so that a box is formed.

Step 3: Attach Desk Base to the Cabinet Face

Using 1 1/4 inch-pocket hole screws and wood glue, attach the desk base to the underside of the cabinet face. Work slowly and do not drive the pocket hole screws too deep so they poke out the other side. Then cut a piece of 1/4-inch plywood to the same dimensions as the cabinet face and attach it to the underside of the desk base with wood glue, 1/2-inch nails and a hammer, spacing nails every 3 inches along the perimeter. An optional alternative to the hammer and nails would be to use a pneumatic or electric nail gun and 18 gauge 1/2-inch nails.

Step 4: Make Holes in the Drawer Face

Using cups or small tin buckets as a template, trace four evenly-spaced circles on the drawer face. If tracing from the base of the cup or bucket, draw the circle about 1/2 inch larger than the actual diameter. Drill holes along the edge of the diameter of the circles with a 1-inch self-feed drill bit, and then use a jigsaw to slowly cut along the perimeter of the circle. Repeat for the remaining three circles.

Step 5: Attach Drawer Face to the Cabinet Face

Place glue along the underside edges of the drawer face and carefully position it on top of the cabinet face over the drawer opening. Use a measuring tape if necessary to make sure placement is even on all sides. Clamp the drawer face to the cabinet face and let it dry overnight.

Step 6: Attach Knob to Cabinet Door or Route the Edge

If the cabinet door sits flush with the cabinet face when closed, a knob will need to be attached to easily open the desk. Measure, mark and drill a hole in the center long edge of the cabinet door (the unhinged side) so that it will not interfere with left- or right-handed children. Attach the knob.

Another option is to route the long edge of the cabinet door so a lip is formed for easier opening of the desk. To do this, position the router table guide at 0 inches so half of the round nose bit cuts into the edge of the door. Remove the screws from the hinges on the cabinet door and slide it along the router table, following the manufacturer’s instructions. Once the door has run through twice (to ensure an even cut along the entire long edge), sand the cut edges with 220 grit sandpaper to remove splinters.

Step 7: Fill Holes and Sand the Desk

Use wood filler to fill the holes from the cabinet pull, seams and places where the desk base join with the cabinet face. Let it dry for several hours. Sand the pre-finished cabinet door, drawer and base with 150 grit sandpaper by hand, or use an orbital sander to remove the protective finish and make it easier for paint to adhere to the surface. Sand the areas where wood filler was used and all edges with 220 grit sandpaper to ensure there are no sharp corners or splinters.

Step 8: Attach Feet to the Desk

On the four corners under the desk base, mark and pre-drill holes for the table leg straight top mounting plates. Attach the table legs into place using the screws provided with the mounting plates. Be sure to screw in the legs until tight.

Step 9: Paint the Desk

Use a 2-inch paintbrush and white latex paint + primer in semi-gloss finish to paint the entire desk, except the center of the cabinet door. Apply two coats and let dry completely. Use a 3-inch foam roller brush to paint the center of the cabinet door with chalkboard paint. Apply two to three coats and let the desk dry for 24 hours.

Step 10: Place Small Tin Buckets in the Holes

Place small tin buckets or cups in the four holes that were cut out earlier, and fill with crayons, pencils, chalk, scissors or other school supplies.

This desk provides great storage for supplies and crafts! Your kids will love it, and you’ll love the contained mess!

0 replies

Leave a Reply

Want to join the discussion?
Feel free to contribute!

Leave a Reply

Your email address will not be published. Required fields are marked *